Fiat 500 Replacement Key Fob
It's possible to replace the battery if the 500 remote key fob is not working. If you replace the battery, but it's still not working it could be the issue elsewhere.
United Locksmith specializes in the production of new keys for classic cars. We have all of the tools and parts necessary for this service.
Dead Coin Battery
The most common reason your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob is equipped with an in-built battery that can quickly deplete when it isn't being frequently used. If your remote is beginning to show signs like a loss of range, or has stopped functioning or not responding, then the battery could be dead.
The battery inside the key fob is held in place by steel retaining clips. If the clips aren't tightly secured, they could result in contact issues that prevent your remote to receive power. With a small flathead screwdriver, push the retaining clip outwards to remove the current battery and replace it with a new one. Make sure to use a battery with the same voltage, size, and specification as the original.
Water exposure can also cause the key fob to corrode or become damaged. Even a short bath in soapy water could harm the electronic chip in. It is best to keep your key fob in a dry place.
Water Damage
Water damage may be the cause of your key fob's inability to function properly. Key fobs have rubber seals that stop them from being damaged by a light rain or a splash of water, however it is very important to keep your keys away from the pool, ocean, and the washing machine!
The key fob has an electronic chip that sends an immobilizer of your car. The chip allows the 500 to be locked and started. If it gets wet it will not function.
If you want to check whether your key fob still functioning you can clean the internal electronics using isopropyl or an electronic cleaner. However, it is probably best to get a replacement from a dealership instead of trying to fix a key fob that was submerged in salt water.
While a replacement fob could cost you a bit of money, it's much less expensive than having to pay for your Fiat 500 to be towed to the dealer for repair! Additionally, you can do it yourself in the simplest of steps. Be sure to use the correct type of battery before you attempt to open your key fob. You can find step-bystep directions for any car keyfob online.
Faulty Chip
The chip inside the key fob communicates with the car's immobiliser system to ensure the vehicle is only able to start when the correct key is inserted. If the chip is damaged, or corrupted in any way the car won't start.
Damage to the water or a dead battery are the most frequent causes of defective chips. Whatever the reason, it's recommended to delegate the job to a locksmith who will be able to repair the chip fast and at a cost-effective price.
If fiat punto key fob does not work after being exposed to clean rain or tap water, remove the battery. Wipe down the electronic component using an old towel. If the key fob will not function, there's the possibility that it's a fried component and needs to be replaced.
A few people turn to their dealer when they are in need of a new Fiat key fob, but it can be a costly option. If you are seeking a cost-effective method to get your Fiat key fob repaired make sure you contact United Locksmith. We have the equipment and know-how to fix your Fiat fob quickly and professionally. manner.
Faulty Receiver Module
Fiat key fobs transmit a signal up 50 feet to the vehicle, which will unlock and close the doors (and start the vehicle in case of automatic transmissions). There are a variety of reasons why the fob may stop working. This could be due to a dead coin battery damaged by water, worn buttons or a problem with the receiver module and signal interference, or an electronic chip malfunctioning.
If the fob is in a pocket that has experienced extreme trauma, like being dropped on hard floor or being washed in the washing machine, it may not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept a signal from a genuine key and not accept any other.
You will need to replace the fob if this happens. A professional locksmith can handle all aspects of the key replacement procedure, including programming a new one for your 500. In fact, they'll offer you a clone key that functions exactly like the original fob (and costs only a fraction of the cost).